Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not underestimate the forklift at work. If the procedure is not good, there will be serious accidents in minutes, and there are several mishaps including forklifts.

Instance 1: The forklift freight blocked the vehicle driver's sight, and the individual ahead might not be discovered, causing a rolling accident.
Case 2: In order to preserve the equilibrium of the forklift when lifting hefty products, the workers utilized their body weight as the counterweight, which practically caused casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift lifts the personnel illegally, the forklift driver does not put on the safety belt, the forklift lifter drops and the driver is squashed when the forklift surrender.
Case 7: The forklift motorist did not put on a safety belt and dropped from the lorry when it rolled over and was crushed.
Forklift operation need to pay attention to these matters ：.

Beginning.
1. Before starting, observe the surroundings, and after validating that there are no barriers that impede the safety and security of driving, honk the horn initially and after that start.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge should be secure prior to starting.
3. When the forklift begins with a tons, the driver ought to first confirm that the load is secure and reputable.
4. The beginning should be slow and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole must be tilted backward. .
2. Do not raise the fork too expensive when driving. When going into and leaving the job website or while driving, be careful that there will certainly be no challenges overhead. When the tons is traveling, the fork needs to not be raised too high, which will certainly influence the security of the forklift. .
3. After unloading, the fork needs to be decreased to the normal driving placement before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal needs to be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly trigger the lorry to shed lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the flame and slide, and it is prohibited to brake unexpectedly while driving with tons unless there are unique situations.
6. When the forklift is running, it should comply with the website traffic rules in the factory and need to keep a certain security distance from the lorry in front. .
7. When the forklift is running, the lots should be in the lowest setting that does not impede the driving, and the gantry must be effectively slanted back. The tons shall not be elevated other than when stacking or loading. .
8. The elevation of the load must not obstruct the motorist's view. In unique circumstances, when the product impacts the forward vision, drive at a low rate when turning around.
9. It is forbidden to switch on the ramp, neither to drive throughout the ramp. .
10. The safe driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a reduced rate when entering the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is prohibited for employees to stand on the fork to hold items and play a balancing duty. .
12. If troubles are found, they will certainly be repaired and reported in a prompt fashion, and they will certainly never operate with health problems or conceal them.

loading and discharging.
1. When fork-loading items, the range in between the two forks need to be adjusted as needed to make the load of the two forks well balanced and not manipulated, and one side of the product should protest the rack. .
2. It is forbidden to collaborate with a solitary fork or utilize a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift needs to be braked with the brake. .
4. The rate of the car ought to be slow and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it should be noted that the fork tip should not touch various other goods or items. The lots must be supported with marginal back tilt of the gantry to ensure that the load does not move in reverse. The mast can be slanted forward a little when the load is lowered to enable easy positioning of the lots and removal of the forks. .
6. It is forbidden to fork goods at high speed and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is prohibited for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Straining is prohibited, and it is restricted to use forks to lift employees to engage in high-altitude operations to stay clear of high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slip, place, round or roll objects. .
10. It is not enabled to utilize forks to select, turn pallet dump.

Leaving .
1. It is restricted to leave the forklift when the products on the fork impend. Before leaving the forklift, you should dump the goods or lower the fork structure.
2. Pull the emergency brake manage to dead or depress the hand brake switch.
3. The engine is turned off and the power is removed. (Except for unique scenarios, such as the chauffeur does not leave the lorry's view and does not exceed 1 min).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be examined, and gas, lubing oil and cooling water need to be added.
2. Examine the safety and security efficiency of starting, running and stopping.
3. Check whether the lights and horn signals are complete and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage must also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You need to inspect prior to leaving the vehicle;.
2. When you come across somebody before you during driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the freight need to be 0.3 m ~ 0.4 m in the air;.
5. The turning ought to not be as well sharp to prevent the tendency of " cost-free switching";.
6. Adding and down the incline must be sluggish and uniform, and no activating the incline is allowed.
7. Do not drive across the gradient. When the gradient is higher Electric Forklift Truck for Warehouse than 10%, the car ought to be driven backwards when declining;.
8. When the forklift employees bring the goods and move forward, if they encounter big or heavy products and go to the chauffeur's line of vision, they must take the reversing exercise
.
The "Eight Prohibitions" should be followed in the operation.
1. Single fork procedure is not enabled.
2. It is not enabled to lift the goods for far away driving.
3. It is not allowed to pick up the goods by passing on the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not allowed Electric Forklift Truck for Warehouse to utilize inertia force to get the goods.
6. It is not allowed to make use of stopping force to exile round or easy-to-roll things.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive side to side on slopes
.
Parking is not permitted under the list below problems.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline above 5%.
3. When there is an challenge on one side of the road, the opposite side of the section with the exact same size as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844